Checkmate XP is the Next Generation Multi-door Cost effective
Access Controller ideally suited where high level security is imperative
along with distributed control. .It manages upto 16 Proximity/Smart
Card /Biometric Reader (Weigand Compatible) installed at various doors in
an organization. The low cost, small, attractively packaged front end
Readers are connected to the Controller in a Star Connection and the Lock
release output is driven from the Controller itself. Hence no intelligent
hardware is required at the door end.
Checkmate XP provides a field configurable intelligent
firmware engine for taking care of any organization’s access control
requirement .The controller can be configured using a front end Software,
COMPRO XP. Once the Checkmate XP is configured, all the Access decisions
are taken by the controller making it truly a standalone system, independent
of PC. It can be used in on-line mode for larger PC Controlled Building Management
System. Multiple Checkmate XP’s can be networked on a RS485 bus
or on a Ethernet Network with suitable hardware for larger application.
Card Reader Technology:One of the following type of card
Reader may be used as front end user interface for Access Control :
MicroTIP : Finger Print Reader
Finger Print Reader works on
Biometric Technology. Upto 2 fingers can be enrolled. The Finger Print Reader
is used as front end reader
at the door. Upon placing the finger, if the user is enrolled, the ID Number
against the finger is identified & the
reader transmits the ID code
for access validation to Checkmate XL. If the card holder is found valid,
then the Access is granted.
MicroSMART : Contact less Smart Card Reader :
Contact less Smart card Reader works on 13.56 MHz RF based on MIFARE technology.
It is useful where Multi- application for employee card is envisaged. MicroSMART,
compliant to ISO 14443 Protocol, can be used (Read Range 3”). HID iClass
Readers may also be used.
MicroPROX : Proximity Card Reader(RF ID) :
Proximity Reader is based on 125 KHz RF technology and reads the Proximity
cards on show within read range .The Entry level MicroPROX reader has a read
range of 3”. HID Prox Point Reader may also be used.
Hardware Features
● 16 Reader Interface
Panel supports 4 Weigand Reader interface. The Reader type supported is Proximity,
Smart Card or Finger Print reader or a mix. Readers can individually be
upto 100 m cable distance from the Controller.
● 16 Relay Output for Lock Operation
The relay outputs are available for Lock Release & are tagged to one
or more Reader for door operation as per requirement.12V wetted contact can
be provided from the built-in Power Supply for Lock operation.
● 16 Exit Push Switch Input
There is a provision for 4 Exit Push Switches & is paired with the lock,
it is going to release. The switch is normal Push Button offering momentary
contact. The lock is operated upon usage for Lock On-Time.
● 16 Door Open Sensor Input
For monitoring the status of the Door (i.e. Open or Close), Door Open Sensor
input is used. The Door open sensor input is paired with a lock. It is
useful for Turnstile operation for locking it upon rotation feedback.
● Built-in Lock Power Supply
A Bulk 12V Power Supply is centrally connected to the controller to
power the locks thereby removing the necessity for power supplies near lock.
Optionally, UPS with battery may be provided.
Access Control Features
● ACCESS GROUP : 16 Access Groups may be defined.
Each Access Group are associated with one or more locks. One or more Readers/Exit
switches are linked to a lock in an Access Group.
● ATTENDANCE GROUP : Attendance Group
is used for recording Employee Attendance and accepts all cards at all time.
These data are later used for Attendance Report generation.
● GLOBAL ATTENDANCE MODE : Access may be granted
only to Card Holders who have Clocked-In the Attendance in the Attendance
Group. Once the Card holder Clock-out, the Access rights to the card holder
is removed. This feature may be enabled to selective Card Holders also. The
Attendance may be done using Biometic reader & the Access Control may
be done using card. If this mode is activated, then loss of a Valid Card
will not lead to security lapse.
● GROUP ANTIPASS BACK :
Enable / Disable for each Access Group. Hard Antipassback : No exit w/o valid
Entry, violation alarm.
● TIME ZONE : 4 user definable Time zones per Access Group.
The Time Zones could be enabled/Disabled for Holiday/Weekly off. “ALLOW
ALL” Time Zone is possible for rush hours.
● CARD HOLDER DATABASE : Each Access Group has its own
set of Card Holders linked to one or more Time Zones for the Group. Card
holder can be member of Multiple Access Groups. Upto 4500 IDs over all the
Access Groups.
The Validity Period of a Card Holder may be defined such that the Card automatically
becomes invalid.
● CALL CENTRE MODE : This feature could be used, if you
want to withdraw Access automatically to a Card Holder, if it is not in use
for a specified No. of days. The No. of day for withdrawing access is definable.
● FACILITY CODE : Upto 8 Valid Facility Code may be downloaded,
such that the Card Nos. of the said Facility code will only get accepted
by the controller. Alternatively, if this feature is not configured, it will
accept the cards from all the facility codes.
● VISITOR DATABASE : A visitor based on entry from
the Central Computer would have access defined based on the Access Group.
The Access rights can be withdrawn upon visitor leaving. Upto 200 visitor
ID database may be defined.
● HOLIDAY DATABASE TABLE : 30 Holiday
Dates & a Weekly off Day can be defined for barring Access. Upto 200
card holders can be provided access irrespective of Holidays based
on their default Access Groups & Time Zones.
● HOLIDAY MASTER CARD : For Card holders
not included in Holiday Database Table, requiring entry on holiday/weekly
off in their Time Zone, Master Card needs to be shown before the Card Holders
card. Upto 5 Holiday master cards per Access Group may be defined.
● DOOR OPEN TO LONG (DOTL) : If the Door open
sensor input is ON for a period longer than the lock on - time, Alarm is
raised & recorded. This may be used for on-line monitoring of doors on
Central Monitoring Computer.
● LOCK ON-TIME :
Lock on-time for door opening after Card Show is User Settable. The Lock
shuts after this time. This can be used with Door open Sensor for exception
monitoring. This could be set for each door separately.
● EMERGENCY OPERATION : All Doors are opened based on Fire
Alarm /closed in case of Burglar Alarm Panel Input. Resetting of Alarms results
in normal operation.All alarms are logged for analysis.
● ACCESS RIGHTS EMERGENCY OPERATION : Card Holders
can be temporarily Enabled/disabled from the Card Holder Table in the Controller.
This feature is useful in case of ID card loss.
● EMERGENCY LOCK OPEN : Central Computer can open a lock
remotely with authorization. All such events are logged.
COMPUTER CONNECTIVITY
Computer can be connected to a single Controller within 15 m using
RS232 , or multiple controllers thru RS485 upto 1.2 Km in bus topology
or thru a add on Ethernet interface for plugging into the TCP/IP network(Optional).The
COMPRO XP software running on the Computer is used for excercising all the
features explained in the Hardware and Firmware section.
Cabling
6 core multi strand (each core 14/36) shielded cable for Reader is
used. One Pair each of electrical multi strand cable(each core 1.5
sq mm) is used for Lock operation, Door Open Sensor and Exit Switch. These
cables run from each Door to Controller. Cable length should
be within 100 m.
COMPRO XP:
Configuration and Report Generation Software
Compro XP software, apart from configuring Checkmate XT to the user’s requirement also downloads the transactions and generates reports for First In Last Out , Movement Report , Access reports for Access groups, visitor IN-OUT reports etc. Data is available in tables for user to create his own reports or to link to their HR/Attendance/Payroll package.
Data Management :
Checkmate XT stores the last 45000 transactions
including the date / time ,ID , Access Area etc. so that movement tracking/Attendance
is possible. The Central Monitoring computer optionally can show the current
location of Person in on-line mode. The Central Monitoring Computer connected
to the Checkmate XT over the Serial RS232C/Ethernet network can do so in a continuous
manner, On-line mode or in a Batch-mode collecting the data from the controller
once in a while manually.
Cards
Proximity cards/Smart cards compatible to respective readers need to be used.
The size of the Card is as per ISO Standard i.e. 85 X 54 mm. The card can be
read even if it is kept in Valet, within the read range.
TECHNICAL INFORMATION
- CPU : 16 bit Microcontroller based design with Real Time Firmware in
Flash ROM
- Memory : 512 KB RAM (40,000 Records Storage), Lithium Battery backed
up RAM
- Watch Dog Timer : Yes
- Battery Back-up : Clock & Data up to 10 years
- Communication : RS 232C or RS485 (Isolated)/Ethernet
- Data Upload Speed : 1000 Records/minute
- Power : SMPS 110 V to 260V @ 50Hz+/-5Hz,12V/10 Amps. SMPS Power Supply
- Card Reader Interface : 16 Nos. Weigand Interface(26/34 Bit)
- Card Holder Database : 4500 Card Holder
- Relay O/p : 16 Potential Free/12V contact o/p
- Exit Switch : 16 Exit Switch Input Interface
- Lock Feedback : 16 Door Open Sensor Interface for Lock Feedback.
- General Purpose Input/Output : 8 GPI & 8 GPO(TTL Level)
- 2X16 Digital Backlit LCD Display
- Dimension : 500(H) X 350 (W) X 85(D) mm
- Mounting : Wall/Panel
- Enclosure/Casing : Dust Resistant Corrosion Free, MS Enclosure.
- Color : Siemens Gray
- Operating Temp. : 0 – 50 Deg.C
- Humidity : 0-95% RH
- Card Reader Interface : 4 Reader 26 bit Weigand Interface
Application Areas
- Software Houses
- Server Room
- Directors Room
- Media Room
- Conference Room
- Main entrance of office
- Facility Room
- Store Room
- Cash/Record/Billing Room
- Canteen Facility
- Telephone Exchange
- Cellular/Paging/Internet Service Providers
- R & D setups
- Defense Labs
ORDERING INFORMATION
- Checkmate XP : Access Controller with 16 Reader
I/F, 16 Relay Output
- Checkmate XP/8 : Access Controller with 8 Reader
I/F,8 Relay output
- Bulk Lock Power Supply: 12V DC/10Amp. SMPS for powering
Locks
- MicroTIP: Integrated Finger Print Reader
- MicroPROX : Proximity Card Reader with Read Range
upto 3"
- MicroSMART : Contactless Smart Card Reader (Read
Range upto 3")
- MiniProx/Prox Point Plus : HID Proximity Card
Reader
- DVR XP : 8 Channel DVR System integrated with Online
Access Control Software
- COMCON : RS232C to RS485 Converter
- COMCON TCP/IP : RS232C to Ethernet Converter on
TCP/IP Protocol
- COMPRO XP : Configuration, Data Capture and Reporting
Software
- MIS Time Pro LITE: Time Office Management Software
- MIS Time Pro Enterprise: Time Office
Management Software for Factory
- PayLITE : Payroll Management Software
- eTIME Pro: Web based Time Office Management Software
- ID Card: (a) Proximity Card (b) Contact Less Smart
Card
- Door Lock: (a)Strike (b)EM Lock (c)Turnstile (d)
DrOp Bolt (e)Boom
- Cable: (a)Reader Cable (b) Communication cable (c)
Lock Cable
- Accessories : (a)Exit Switch (b) Door Sensor
|
